Latin Tech Inc. FAQs

This is most likely due to the serial driver not being able to load properly and the WinTRiLOGI closes itself down when the exception occurred. There are a few possibile reasons:

1) There are more than one version of Java runtime Environment in the PC (JRE). Some newest Windows PC now comes pre-installed with a JRE (1.4.x), and if you install the JRE 1.3.1 over it, a conflict may occur causing the serial driver file not being able to load properly. To check if you have a pre-installed JRE, go to the "Command Prompt" and enter the following command:

C:\> java -version

If it shows that the PC already has a version 1.4.x, then do not install the JRE 1.3.1 over it. However, if you have already installed the JRE 1.3.1 then a conflict would have occurred.

To resolve this conflict, you need to first uninstall both the JRE 1.3.1 and the JRE 1.4.x that have been installed on the PC by going to the "Control Panel" to remove both the JRE. Next, go to the following link to download the latest version of Java JRE 1.4.2:

http://java.sun.com/j2se/1.4.2/download.html

Please download only the "J2SE Java Runtime environment", not the SDK (unless you plan to write Java program using the SDK). Now install the JRE 1.4.2 and make it the only JRE on your system.

You can now run the "SetupWTL3.exe" program to install the WinTRiLOGI program again. The setup program will now be able to properly install the serial driver into the correct JRE sub-folder and you should be able to run the WinTRiLOGI program properly.

2) If your PC does not already have a Java Runtime Environment, but you have installed the WinTRiLOGI before installing the JRE then the WinTRiLOGI setup program would not know where to properly install the serial driver file.

The solution is to re-install the WinTRiLOGI program again after the JRE has been installed. This way the WinTRiLOGI program can properly install the serial driver into the correct JRE folder and the program should run.

3) If for some reasons the setup program is unable to install the serial driver file into the correct JRE folder. In that case you should manually copy the serial driver file into the appropriate JRE folder. Please refer to the follow link for details:

http://www.lt-automation.com/downloads/TLServer%20could%20not%20start.pdf

	Pilot Plants PLCs PLC Training Books Remote Modules Voice Modules	Position Transducers Wireless Modem Power Supplies Operator Panels Scadas	Who are we? Our customers FAQS How to order Contact Us Home
Latin-Tech Inc.

			Español	English

PH: 305 848 3517 8004 NW 154ST #621 Miami Lakes, FL 33016 USA


		FAQ

PLCs	Indusoft

PLCs

WinTRiLOGI disappear after selecting PLC Type
This is most likely due to the serial driver not being able to load properly and the WinTRiLOGI closes itself down when the exception occurred. There are a few possibile reasons: 1) There are more than one version of Java runtime Environment in the PC (JRE). Some newest Windows PC now comes pre-installed with a JRE (1.4.x), and if you install the JRE 1.3.1 over it, a conflict may occur causing the serial driver file not being able to load properly. To check if you have a pre-installed JRE, go to the "Command Prompt" and enter the following command: C:\> java -version If it shows that the PC already has a version 1.4.x, then do not install the JRE 1.3.1 over it. However, if you have already installed the JRE 1.3.1 then a conflict would have occurred. To resolve this conflict, you need to first uninstall both the JRE 1.3.1 and the JRE 1.4.x that have been installed on the PC by going to the "Control Panel" to remove both the JRE. Next, go to the following link to download the latest version of Java JRE 1.4.2: http://java.sun.com/j2se/1.4.2/download.html Please download only the "J2SE Java Runtime environment", not the SDK (unless you plan to write Java program using the SDK). Now install the JRE 1.4.2 and make it the only JRE on your system. You can now run the "SetupWTL3.exe" program to install the WinTRiLOGI program again. The setup program will now be able to properly install the serial driver into the correct JRE sub-folder and you should be able to run the WinTRiLOGI program properly. 2) If your PC does not already have a Java Runtime Environment, but you have installed the WinTRiLOGI before installing the JRE then the WinTRiLOGI setup program would not know where to properly install the serial driver file. The solution is to re-install the WinTRiLOGI program again after the JRE has been installed. This way the WinTRiLOGI program can properly install the serial driver into the correct JRE folder and the program should run. 3) If for some reasons the setup program is unable to install the serial driver file into the correct JRE folder. In that case you should manually copy the serial driver file into the appropriate JRE folder. Please refer to the follow link for details: http://www.lt-automation.com/downloads/TLServer%20could%20not%20start.pdf

Indusoft

Indusoft Demo
You can download the full scada package and the manual from http://www.indusoft.com/zip/webstudio60/iws60d1.zip ; it will run for 40 hours. The service pack 5: http://www.indusoft.com.br/download/webstudio60/iws60sp5.zip Getting started guide: http://www.indusoft.com/zip/webstudio60/Manuals/GettingStarted.pdf User guide: http://www.indusoft.com/zip/webstudio60/Manuals/UserGuideV60SP5.pdf Indusoft and ISaGRAF Communicate on theWinCON Indusoft and ISaGRAF Communicate on theWinCON

				UP

For any additional information please CONTACT US, let us know what you need!!


			© LATIN TECH 2005